# Retaining Wall Network

0

HEREISCONTENT

April 14, 2016 |

## Tiered Retaining Walls

0

When one retaining wall is constructed above another retaining wall, the two walls together are called a Tiered Wall System.  Tiered walls look like this:

When dealing with tiered walls, a retaining wall contractor will ask:
1. How far apart are the walls?
2. How high are the walls?
3. Are they really two separate, independent walls?
4. Do the two tiers of wall join and become one (merged) wall?

Distance Between Tiers:
Extra loads on a retaining wall are called surcharges.  Retaining wall contractors understand that as the Upper Wall gets closer to the Lower Wall there is more load (more surcharge) put on the Lower Wall.  If the Upper Wall is far away, then there is less load (less surcharge) put on the Lower Wall.

Question: How far away must the Upper Wall be so that it will not surcharge the Lower Wall?  Answer: Take the height of the Lower Wall and double that number.  That is how far away the Upper Wall must be to apply little to no surcharge on the Lower Wall.  For example, if the Lower Wall is five (5) feet high, then the Upper Wall must be at least 10 feet back from the Lower Wall so it won’t overload the Lower Wall.  (This assumes that the Lower Wall is taller than the Upper Wall.)  See this drawing:

Question: Can the Lower Wall be specially designed for the surcharge of the Upper Wall?  Answer: Yes, definitely!  A retaining wall engineer can design the Lower Wall for the surcharge load applied by the Upper Wall.  In the NCMA* Design Manual (2010, Third Ed.) use Figure 5-6, “Surcharge Approximation for Tiered Walls”.Question: Can I have a single wall that “splits” apart, with the bottom half curving away from the top half?  Yes!  Retaining wall contractors and engineers have become very creative, with splitting (or merging) walls.  The most important thing to remember is that you must provide support below the upper blocks when the upper part of the wall curves away from the lower part of the wall!  See this sketch for a concept drawing of burying blocks to support that upper wall:
Remember, tiered walls can be a beautiful way to improve a retaining wall design and layout.  But the tiers have to be designed properly to be structurally sound.

*National Concrete Masonry Association, Design Manual for Segmental Retaining Walls, Third Edition, Fifth Printing, 2010, Copyright NCMA, Herndon, VA.

February 4, 2014 |

## Retaining Wall Design Contracts

0

Obviously, retaining wall design involves contracts.  These contracts between the Engineer and the Client are important.  Does the contract benefit both parties?  Is using contracts a win-win?

Contracts are important to:

1. Memorialize everyone’s understanding of each party’s roles and responsibilities;
2. Reach a mutual understanding of the project requirements;
3. Establish the rules to which the parties will adhere; and,
4. To identify and allocate risk fairly.

A good contract fairly allocates reasonable risk to both parties, based on the benefits of the project to each party.

Here’s an example of fair allocation of reasonable risk:  when the contract includes a Limitation of Liability for the Engineer.  Why, you might ask, am I limiting the Engineer’s liability and how is that fair?

Well, here’s how it is fair:  The Engineer doesn’t demand an Unlimited Fee.  With an unlimited fee comes unlimited liability.  With a limited fee there is limited liability.

Sounds fair to me.  What do you think?

December 13, 2013 |

## Retaining Wall on Sliding Soils

0
The old retaining wall (which failed) was constructed on soils that were sliding downhill!  The rock was too deep to put the new retaining wall on the bedrock, so we drilled piers down to the bedrock to stop the hill from sliding and to support the new retaining wall.

This video shows you how to prevent a retaining wall failure when there are sliding soils!

December 9, 2013 |

## Easley, SC

0

Retaining wall expert project Number 13007 included several retaining walls in Easley, South Carolina.

August 30, 2013 |